- Home
- ยป
- Products & Services
- »
- Piston Pump
Piston Pump
Gold Cup PV14 Series Denison Piston Pump
View Brochure
Brand | Denison |
Model Name/Number | PV14 Series |
Usage/Application | Hydraulic Equipment |
Frequency | 50 Hz |
Voltage | 210 V |
Color | Grey |
Weight | 73 lb {33 kg} |
Off-Stroke Compensator Response | 50ms |
Input Mounting | 127-2 (C) |
Max Speed | 2400 RPM |
Rotating Inertia | 21.84 lb in2{.00647 kg m2} |
Intermittent Pressure | 4000 Psi {280 bar} |
On-Stroke Compensator Response | 120ms |
Max Compensator Setting | 4000 Psi {276 bar} |
Minimum Inlet at 1800 rpm | -6.1 in-Hg {-155 mm-Hg} |
Maximum Inlet Pressure | 50 Psi {3.4 bar} |
Continuous Pressure | 3000 Psi {207 bar} |
Displacement | 3.78 in3/rev {61.9 cm3/rev} |
Maximum Case Pressure | 10 Psi {0.7 bar} |
Compensator Adjustment | 650 Psi/turn {44.8 bar/turn} |
The PV series pumps are variable displacement open circuit piston pumps with a design emphasis on operation economy. These axial piston pumps for open loop operation are suitable for rear drive in the PVT series configuration. The PV pumps have a displacement of 0.88 to 7.93 cu. in/rev. (14,4 to 130,0 cc/rev.) with a continuous working pressure up to 4000 psi (280 bar): The pumps can be equipped with a pressure compensator, ventable compensator, load sensing or power limit control.
MountingThe PV pumps have been designed to operate in a wide range of applications in industries where high pressure and variable flow are required at competitive cost. These pumps are designed to operate in any position. The mounting hub and two bolt mounting flange are in conformance with SAE standards. The pump shaft must be in alignment with the shaft of the source driver and should be checked with a dial indicator. The mating pilot bore and coupling must be concentric. This concentricity is particularly important if the shaft is rigidly connected to the driven load without a flexible coupling.
Input Shaft Information Splined:The shafts will accept a maximum misalignment of 0.002 in. (0,06mm) total indicator reading when the pump is foot mounted and 0.001 in. (0,03 mm) when flange mounted. Angular misalignment at the male and female spline axis must be less than ±0,002 inch per inch radius (± 0,002 mm/mm). The coupling interface must be lubricated. DENISON recommends lithium molydisulfide or similar grease. The female coupling should be hardened to 27/34 Rc and must conform to SAE-J498c, class 5 flat root side fit.
Keyed:High strength heat treated keys must be used. Replacement keys must be hardened to 27-34 Rc. The key corners must be chamfered 0.03 - 0.04 in. (0,75-1,0 mm) at 45° to clear radii that exist in the keyway.
Side Load CapabilityThe PV series is designed for inline-drive and side loading on the shaft is not recommended. If this is unavoidable consult your nearest DENISON HYDRAULICS representative.
Direct EquivalentReplace your old Denison PV with the Continental HPV range of piston pumps. Output flow sizes are equal to the Denison pumps including the 6, 10, 15, 20 and 29 gallons per minute @ 1750 RPM units. Contact us with your Denison PV part number for a direct Continental hydraulics HPV replacement pump.
NN HTDRAULIC INDIA is the leading supplier of HYDRAULIC MOTOR/HYDRAULIC MOTOR REPAIRING SERVICE/HYDRAULIC PUMP/HYDRO PUMP of all companies.
we have the best quality of HYDRAULIC MOTOR/HYDRAULIC MOTOR REPAIRING SERVICE/HYDRAULIC PUMP/HYDRO PUMP
we have the large variety of HYDRAULIC MOTOR/HYDRAULIC MOTOR REPAIRING SERVICE/HYDRAULIC PUMP/HYDRO PUMP.
we have the best quality of HYDRAULIC MOTOR/HYDRAULIC MOTOR REPAIRING SERVICE/HYDRAULIC PUMP/HYDRO PUMP.
we deal in PAN INDIA
90R55 Danfoss Piston Pump
Brand | Danfoss |
Model Name/Number | A17FO |
Usage/Application | Hydraulic Equipment |
Material | Cast Iron |
Maximum Pressure | 400 bar |
Size | G 3/4; 16 mm deep |
Temperature Range | -25 Degree C |
Viscosity Range | Nmax < 1600 mm2/s |
Rate of pressure change | 9000 bar/s |
Nominal Pressure Bar | 350 bar |
Single operating period | 5 Sec |
Total operating period | 50 H |
Minimum pressure | 10 Bar |
- Flange and shaft designed for direct mounting on the power take-off of commercial vehicles
- Optimized weight by cast aluminum housing
- No drain line required
- Low operating noise
- Simple adjustment of rotatonal direction
- Excellent suction characteristics
- High total efficiency
- Long service life
- Bent-axis design
A2F107 Rexroth Bend Axial Piston Pump
Brand | Bosch Rexroth |
Model Name/Number | A2F107 |
Usage/Application | Hydraulic Equipment |
Power | 14.5 kW |
Material | Cast Iron |
Flow | 27.6 l/min |
Maximum Pressure | 350 Bar |
Frequency | 50 Hz |
Voltage | 210 V |
Color | Black |
Maximum Speed | 5600 RPM |
Moment Of Inertia For Rotary Group | 0.00006 kg.m2 |
Nominal Pressure | 315 bar |
Rotary Stiffness | 0.63 kNm/rad |
Torque | 24.7 Nm |
Displacement | 4.93 cm3 |
Weight (approx.) | 2.5 Kg |
- Robust pump with long service life
- Very high total efficiency
- High power density
- Large variety of available nominal sizes allows exact adjustment to the application
- Optional with long-life bearings for the nominal sizes 250 to 1000
- Bent-axis design
Rexroth Hydraulic Piston Pump
Pump Type | Hydraulic Piston Pump |
Model Name/Number | A4VG71 |
Brand | Rexroth |
Power | pressure |
Power Source | pressure |
Motor Speed | 3000 RPM |
Brueninghaus hydromatik pump
A4VG71 A4VG90 A4VG125 A4VG250
NN HTDRAULIC INDIA is the leading supplier of HYDRAULIC MOTOR/HYDRAULIC MOTOR REPAIRING SERVICE/HYDRAULIC PUMP/HYDRO PUMP of all companies.
we have the best quality of HYDRAULIC MOTOR/HYDRAULIC MOTOR REPAIRING SERVICE/HYDRAULIC PUMP/HYDRO PUMP
we have the large variety of HYDRAULIC MOTOR/HYDRAULIC MOTOR REPAIRING SERVICE/HYDRAULIC PUMP/HYDRO PUMP.
we have the best quality of HYDRAULIC MOTOR/HYDRAULIC MOTOR REPAIRING SERVICE/HYDRAULIC PUMP/HYDRO PUMP.
we deal in PAN INDIA
Piston Pump A4vso
Pump Type | Radial Piston Pumps |
Model Name/Number | Piston Pump A4vso |
Brand | Piston Pump A4vso |
Power | Piston Pump A4vso |
Usage/Application | Piston Pump A4vso |
Power Source | AC Powered |
Automation Grade | Automatic |
Motor Horsepower | 3 HP |
Ar Series Piston Pump
Pump Type | Radial Piston Pumps |
Model Name/Number | Ar Series Piston Pump |
Brand | Ar Series Piston Pump |
Power | Ar Series Piston Pump |
Usage/Application | Ar Series Piston Pump |
Power Source | AC Powered |
Automation Grade | Automatic |
Motor Horsepower | 3 HP |
AC Powered Hydraulic Piston Pump A10VG18
Pump Type | Radial Piston Pumps |
Model Name/Number | AC Powered Hydraulic Piston Pump A10VG18 |
Brand | Rexroth |
Usage/Application | Hydraulic Pump |
Power Source | AC Powered |
Automation Grade | Automatic |
Motor Horsepower | 3 HP |
AC Powered Industrial Hydraulic Piston Pump Rexroth
Model Name/Number | AC Powered Industrial Hydraulic Piston Pump Rexroth |
Brand | AC Powered Industrial Hydraulic Piston Pump Rexroth |
Power | AC Powered Industrial Hydraulic Piston Pump Rexroth |
Usage/Application | AC Powered Industrial Hydraulic Piston Pump Rexroth |
Power Source | AC Powered |
Automation Grade | Automatic |
Motor Horsepower | 3 HP |
Danfoss Piston Pump
Power Source | DC Powered |
Motor Horsepower | 2 HP |
Type Of Pump | hydraulic pump |
Type Of Hydraulic Pump | Hydraulic Pump |
Model Name/Number | 90R55 |
Payment Mode | Online/Offline |
PVS-1B-16 Nachi Piston Pump
View Brochure
Brand | Nachi |
Head | 15m |
Model Name/Number | PVS-1B-16 |
Usage/Application | Hydraulic Equipment |
Material | Cast Iron |
Power Source | AC Powered |
Frequency | 60 Hz |
Voltage | 210 V |
Color | Yellow |
Case Volume | 16.5 cm3/rev |
Permittedpeakpressure | 25 MPa |
Max. Rotating speed | 2000 Min |
Pressure adjustment range | 2 to 3.5 {20.4 to 35.7} MPa |
Min. Rotating speed | 500 Min |
Mass | 10.5 kg |
Discharge volume | 16.5 l/min |
NN HTDRAULIC INDIA is the leading supplier of HYDRAULIC MOTOR/HYDRAULIC MOTOR REPAIRING SERVICE/HYDRAULIC PUMP/HYDRO PUMP of all companies.
we have the best quality of HYDRAULIC MOTOR/HYDRAULIC MOTOR REPAIRING SERVICE/HYDRAULIC PUMP/HYDRO PUMP
we have the large variety of HYDRAULIC MOTOR/HYDRAULIC MOTOR REPAIRING SERVICE/HYDRAULIC PUMP/HYDRO PUMP.
we have the best quality of HYDRAULIC MOTOR/HYDRAULIC MOTOR REPAIRING SERVICE/HYDRAULIC PUMP/HYDRO PUMP.
we deal in PAN INDIA
Yuken A56 FR 04 HK 32 Piston Pump
View Brochure
Brand | Yuken |
Model Name/Number | A56 |
Usage/Application | Hydraulic Equipment |
Material | Cast Iron |
Mass | 17kg |
Geometric Displacement | 16.3 cm3/rev |
Rated Pressure | 315 Kgf/cm2 |
Viscosity | 20 - 400 mm2/sec |
Minimum Adj. Flow | 8.0 cm3/rev |
Max. Oper. Pressure | 350 Kgf/cm2 |
Suction Pressure | -0.167~0.5 Kgf/cm2 at 600-1800 r/min. 0~0.5 Kgf/cm2 at speed above 1800 r/min. |
Seal Material | FKM (Fluoro Rubber) |
Shaft Speed Range | Max 3600 r/min , Min 600 r/min |
Features :
- Wide assortment of models to ensure interchangeability with pumps available on the global market.
- European models: Compatible with ISO 3019-2, North American models: Compatible with SAE J744.Standard models are available with keyed or splined shaft end.
- Wide displacement range and high volumetric efficiency
- While inheriting the high performance of A3H series pumps, A3HG series pumps feature higher rated pressure design 315 Kgf/cm2. They can be used as pumps capable of handling moderate to high loads in a wide range of applications.
- AEIC-A-1004-083Through drive supplied as standardThe through drive allows for multiple pump installation with a pump on the drive side and another pump with up to the same capacity as the other pump on the non-drive side. All pumps meeting international standards can be used on the non-drive side.
- Control typesPressure compensator type (01), pressure compensator type with external pilot (07), and load sensing type (14) are available.
Atos Axial Piston Pump
View Brochure
Brand | Atos |
Model Name/Number | PVPC - L - 4046 |
Usage/Application | Hydraulic Equipment |
Material | Cast Iron |
Maximum Pressure | 350 Bar |
Displacement Geometric, Per Revolution | 29 / 140 cm3/rev |
Displacement Version | Variable |
Theoretical max flow at 1450 rpm | 42 l/min |
Max displacement | 29 cm3/rev |
Body volume | 0.7 Litre |
Min/Max inlet pressure | 0.8/25 Bar |
Power consumption at 1450 rpm | 19.9 kW |
Max torque on the shaft | 210/270 Nm |
Max pressure on drain port | 1.5 Bar |
Speed rating | 3000 RPM |
Max working pressure / Peak | 280 Bar |
Axial pistons pump with mechanical controls. Manual or remote pressure compensator, load sensing, constant power
K3VL112 Kawasaki Hydraulic Piston Pump
View Brochure
Pump Type | Radial Piston Pumps |
Model Name/Number | K3VL112 |
Brand | Kawasaki |
Power Source | DC Powered |
Motor Speed | 1000 RPM |
Discharge | 70-100 LPH |
Material | Cast Iron |
Motor Horsepower | 3 HP |
Automation Grade | Automatic |
Color | Red |
The K3VL series swash plate type axial piston pumps are designed to satisfy a variety of construction and off-highway applications where a medium to high pressure variable displacement pump is required.
> 28 to 200cc displacements
> 320 bar continuous pressure rating
> Load sensing, torque limiting and electronic displacement control
> Integral impellor pump available on 200cc unit
> *NEW* ATEX option now available!
A10VSO140-DFLR Rexroth Piston Pump
View Brochure
Brand | Rexroth |
Model Name/Number | A10VSO140-DFLR |
Usage/Application | Hydraulic Equipment |
Power | 156 kW |
Nominal Pressure | 4100 Psi (280 bar) |
Maximum Pressure | 5100 Psi (350 bar) |
Flow | 67 gpm |
Torque | 460 lb-ft |
Head | 10 m |
Frequency | 50 Hz |
Voltage | 210 V |
Color | Blue |
Case Volume | 0.790 gal |
Material | Cast Iron |
Displacement Version | Variable |
Total operating period | 300h |
Rotational speed | 1800 RPM |
Minimum pressure | 145 Psi (10 bar) |
Weight (approx.) | 29 Kg |
Displacement | 28 cm3 |
Single operating period | 2ms |
- Variable pump with axial piston rotary group in swash-plate design for hydrostatic drives in open circuit.
- The flow is proportional to the drive speed and displace-ment.
- The flow can be infinitely varied by adjusting the swash-plate angle.
- 2 drain ports
- Excellent suction performance
- Low noise level
- Long service life
- Favorable power/weight ratio
- Versatile controller range
- Short control time
- The through drive is suitable for adding gear pumps and axial piston pumps up to the same size, i.e., 100% through drive.
- Suitable for operation with mineral oil and HF hydraulic fluids
Linde Piston Pump
Model Name/Number | Linde Piston Pump |
Usage/Application | Hydraulic Equipment |
Power | Linde Piston Pump |
Power Source | AC Powered |
Flow | Linde Piston Pump |
Maximum Pressure | Linde Piston Pump |
Displacement Version | Fixed, Variable |
Country of Origin | Made in India |
NN HTDRAULIC INDIA is the leading supplier of HYDRAULIC MOTOR/HYDRAULIC MOTOR REPAIRING SERVICE/HYDRAULIC PUMP/HYDRO PUMP of all companies.
we have the best quality of HYDRAULIC MOTOR/HYDRAULIC MOTOR REPAIRING SERVICE/HYDRAULIC PUMP/HYDRO PUMP
we have the large variety of HYDRAULIC MOTOR/HYDRAULIC MOTOR REPAIRING SERVICE/HYDRAULIC PUMP/HYDRO PUMP.
we have the best quality of HYDRAULIC MOTOR/HYDRAULIC MOTOR REPAIRING SERVICE/HYDRAULIC PUMP/HYDRO PUMP.
we deal in PAN INDIA
A2FO80 Axial Piston Pump
Brand | A2FO80 Axial Piston Pump |
Model Name/Number | A2FO80 Axial Piston Pump |
Usage/Application | Hydraulic Equipment |
Power | A2FO80 Axial Piston Pump |
Power Source | AC Powered |
Flow | A2FO80 Axial Piston Pump |
Maximum Pressure | A2FO80 Axial Piston Pump |
Displacement Version | Fixed, Variable |
Country of Origin | Made in India |
A2FO80 Axial Piston Pump
Brand | A2FO80 Axial Piston Pump |
Model Name/Number | A2FO80 Axial Piston Pump |
Usage/Application | Hydraulic Equipment |
Power | A2FO80 Axial Piston Pump |
Power Source | AC Powered |
Flow | A2FO80 Axial Piston Pump |
Displacement Version | Fixed, Variable |
Country of Origin | Made in India |
Denison Pistol Pump
Flow Rate | 20 LPM |
Usage/Application | Industrial |
Power Source | DC Powered |
Automation Grade | Semi-Automatic |
Motor Horsepower | 2 HP |
Pressure | 30 Bar |
Type Of Pump | Hydraulic Pump |
Type Of Hydraulic Pump | Hydraulic Pump |
Payment Mode | Online/Offline |
NN HTDRAULIC INDIA is the leading supplier of HYDRAULIC MOTOR/HYDRAULIC MOTOR REPAIRING SERVICE/HYDRAULIC PUMP/HYDRO PUMP of all companies.
we have the best quality of HYDRAULIC MOTOR/HYDRAULIC MOTOR REPAIRING SERVICE/HYDRAULIC PUMP/HYDRO PUMP
we have the large variety of HYDRAULIC MOTOR/HYDRAULIC MOTOR REPAIRING SERVICE/HYDRAULIC PUMP/HYDRO PUMP.
we have the best quality of HYDRAULIC MOTOR/HYDRAULIC MOTOR REPAIRING SERVICE/HYDRAULIC PUMP/HYDRO PUMP.
we deal in PAN INDIA
Kawasaki Piston Pump K3VL80
Pump Type | Radial Piston Pumps |
Model Name/Number | K3VL80 K3V80 K3VLO112 |
Brand | KAWASAKI |
Power | KAWAKAKI |
Usage/Application | hydraulic |
Power Source | Hydraulic |
Motor Speed | 3000 RPM |
NN HTDRAULIC INDIA is the leading supplier of HYDRAULIC MOTOR/HYDRAULIC MOTOR REPAIRING SERVICE/HYDRAULIC PUMP/HYDRO PUMP of all companies.
we have the best quality of HYDRAULIC MOTOR/HYDRAULIC MOTOR REPAIRING SERVICE/HYDRAULIC PUMP/HYDRO PUMP
we have the large variety of HYDRAULIC MOTOR/HYDRAULIC MOTOR REPAIRING SERVICE/HYDRAULIC PUMP/HYDRO PUMP.
we have the best quality of HYDRAULIC MOTOR/HYDRAULIC MOTOR REPAIRING SERVICE/HYDRAULIC PUMP/HYDRO PUMP.
we deal in PAN INDIA
V70A Daikin Piston Pump
View Brochure
Brand | Daikin |
Model Name/Number | V70A |
Usage/Application | Hydraulic Equipment |
Power Source | Hydraulic Drive |
Material | Cast Iron |
Voltage | A: AC 100 V (50/60 Hz), AC 110 V (60 Hz) |
Pressure | 2.1 MPa {21 kgf/cm2 |
Displacement Version | Fixed |
Permissible rotational speed | 500 to 1800 min |
Mass (Control method A) | 55 kg |
Pump capacity | 69.8 cm3/rev |
Discharge rate adjustment range | 13 to 126 l/min |
Features :
- Low noise operation over the entire pressure range has been realized in each series.
- High efficiency Fluid temperature rise can be reduced due to the smaller power loss. This means that the tank can be designed in a small size.
- High reliability High responsivity, high stability, and long life make it possible to increase the reliability of the main machine